12/2018
4, 47 NEWS
EQUIPMENT
9 Mixing of high viscosity materials — Herman Hockmeyer
12 Analysis of pigments using laser diffraction PSA
15 Shear forces and scale-up — Herman Hockmeyer
RAW MATERIALS. INTERMEDIATES AND PRODUCTS
18 Alkyds new trade mark ATTALATE — Galkina Yu. V.
ИНТЕРВЬЮ
21 TSENTRLAK answered to America
PRODUCTS AND RESEARCH
28 Investigation of barrier properties and critical level of filling of coatings on the basis of water film-forming dispersions of
anticorrosive application —Prof. Stepin S.N., Ph.D. Katnov V.E., Ph.D. Svetlakov A.P., Rabbanieva E.S.
Abstract:
A consequence of obvious economic and ecological advantages of materials on the basis of water dispersions of film-forming polymers is the steady trend of increase of their share in the total amount of the manufacturing paint and varnish products. Low level of filling and increased hydrophilicity of coatings on their basis belongs to the factors constraining the use of water-dispersible paints and varnishes. It especially concerns anticorrosive coatings, which barrier properties badly worsen at high water absorption and excessive filling. Moreover, low critical pigment volume concentration of pigments in coatings limits possibilities of use of cheap fillers, which content considerably influences the price of coating.
Results of research of operating properties and ability to filling of a number of commercially available acrylate water dispersions, which producers present them as a film-forming basis of anticorrosive water-dispersible primers are given in this work. The received results allow to range the studied dispersions on the quality indicators and to choose objects for development of the innovative filled anticorrosive compositions.
Keywords: acrylate water dispersions, granulometric composition, coatings, barrier properties, adhesion, critical pigment volume concentration.
32 Influence of coalescents on freeze-thaw stability of styrene-acrylate latex and properties of coatings — Ph.D. Krikotnenko V.S., bachelor Pekarsky M.G., Ph. D., Prof. Tolmachev I.A., scientific researcher Petrenko N.A.
Abstract:
The work involved the influence of coalescents most commonly used in the formulations of waterborne paints and varnishes (texanol, butyl cellosolve (BC), butyldiglycol acetate (BDGA), UCAR Filmer iBT, Nexcoat NX-795, isopropyl alcohol (IPA) on freeze-thaw stability of styrene-acrylate copolymer latexes. It was shown that in the presence of coalescents take place a decrease in freeze-thaw stability. Using the three-phase model of the latex system and assessing the degree of swelling of latex films in aqueous solutions and coalescent emulsions, the obtained data was analyzed and it was shown that the effect of coalescents on the latex frost resistance is determined by the place of its localization in the latex system: in the presence of coalescents localized in the aqueous phase (IPA, BC) freeze-thaw stability decreases slightly, and the most significant decrease in freeze-thaw stability is observed for latex containing coalescent localized in the core of latex particles (texanol, UCAR Filmer iBT).
The evaluation of the technical performance of latex films and coatings formed from compositions containing mixtures of coalescents that differ in localization latex system has been carried out. It was found established that in a certain area of the ratios of the components of the coalescing mixture there is an increased frost resistance of the compositions, and coatings based on them have high hardness and relatively low hydrophilicity and water permeability.
Keywords: latex, freeze-thaw stability, coalescents, acrylate copolymers.
EVENTS
24 Exhibition «Chemistry-2018»: the main events of the industry
36 International Coatings Forum: reload — Andrutskaya O. M.
POINT OF VIEW
38 Collaborating on five strategic challenges — Ph.D. Kaverinsky V. S.
40 YOUR NAVIGATOR
INDEX
43 List of articles published in 2018
|
11/2018
4, 48 NEWS
BRANCH MARKETING
14 Additives. Market structure in Russia, price forecast
ECONOMICS AND STATISTICS
17 Forecast of development the materials for road marking market in Russia until 2025 — Ph.D. Kislova Yu. E.
Abstract:
Studied the demand for materials for road marking, as well as the volume of production of this type of paints. Data on domestic production and imports are presented. The factors deterring/favoring to the development of the market of coatings for road marking are described. Made forecasts of development of the market of coatings for road marking and average market prices until 2025 according to three scenarios: baseline, optimistic and pessimistic.
Keywords: materials for road marking, production, scenario forecast.
RAW MATERIALS. INTERMEDIATES AND PRODUCTS
22 Durable road markings thermoplastic acrylic resin ATTALATE A 526 — Galkina Yu. V., Nikolskaya O. S.
Abstract:
Has been developed the formulation of one-component paint for road markings based on thermoplastic acrylic resin Attalate A 526 that meeting all customer demands and tough conditions of the road surface. The coating was tested for wear resistance, hardness, adhesion, opacity and content of non-volatile organic compounds according to the approved methods. The test results showed that the paints can increase the thickness of the applied layer, have improved adhesion, increased wear resistance, durability and low solvent content.
Keywords: road marking, acrylic resins, wear resistance.
INTERVIEW
24 Development line
SUSTAINABILITY AND RESOURCE EFFICIENCY
30 The concept of sustainable development — the driving force of innovation at Covestro — Yeroma Boris
METHODS OF TESTING
38 Road marking with water based materials
EXPERT VIEW
40 The value of online sales for manufacturers of coatings
EVENTS
25 Course on innovations — Andrutskaya O. M.
36 Prospects of the Russian market of high-tech polymers — Andrutskaya O. M.
ANNIVERSARIES
16 Gennady Agafonov is 80 years
42 St. Petersburg state technological Institute celebrates its' anniversary
44 YOUR NAVIGATOR
|
10/2018
4, 43 NEWS
BRANCH MARKETING
10 Pigments. Dynamics and forecast of prices for the pigments according to the types till 2025
EXPERT VIEW
11 Some problems of coatings production
SUSTAINABILITY AND RESOURCE EFFICIENCY
14 Biobased polymers in powder paints
16 Prospects and advantages of bio raw materials for coatings
18 Effect of registration of low volume chemicals in Europe on the paint business
21 Renewable raw materials for emulsion polymers
Abstract:
New monomers synthesized from renewable raw materials are investigated. The comparison of properties: water absorption, gloss, hardness, abrasion resistance, viscosity, chemical resistance in comparison with the reference samples containing standard monomers butyl methacrylate, styrene, vinyl acetate was done. The test results demonstrate a good potential to achieve the same level of properties (and even better) with bio-renewable monomers as the currently used analogues on hydrocarbon raw materials.
Keywords: sustainability, renewable raw materials, emulsion polymerization.
36 Coatings for clear air is new market’s trend
NANOTECHNOLOGIES
24 Graphene nanotubes: conductivity and color in antistatic coatings — Pavlushkova E. V., Chebochakov D. S., Ph. D. Il'in E. S.,
Academic Predtechensky M. R.
Abstract:
The physical properties of graphene nanotubes are considered. The surface resistivity measurement was performed in accordance with the standard method for determining the current conductivity in insulating materials (ASTM D257). To measure the surface resistance of the finished coating, an analog device Desco 19784 was used. Volume resistivity in epoxy and polyester resins at different concentrations of graphene nanotubes has been studied. It is shown that the addition of graphene nanotubes in the formulation of the paint improves the hardness, abrasion resistance, adhesion, allows to produce bright colors coatings with antistatic properties. Examples of practical application in industry are given.
Keywords: nanotubes, graphene, antistatic coatings.
METHODS OF TESTING
32 Possibility of topological calculation of filler mixtures in decorative materials with preference of small fractions. Part II — Furman N. N.
Abstract:
A method is proposed for calculating the packing density of filler mixtures with an excess of a finer fraction. A mathematical model of calculation is presented. The packing density and coordination numbers in the layer of abutment of spherical fine particles to a large particle are calculated, depending on the ratio of their sizes. The tendency to change the packing density has been revealed. On the example of two mixtures of micro-marble, the practical applicability of this method is illustrated.
Keywords: discrete topology, packing density, coordination number, fillers, decorative plaster, micro-marble.
EVENTS
28 Together again— Andrutskaya O. M.
39 YOUR NAVIGATOR
|
9/2018
4, 52 NEWS
ECONOMICS AND STATISTICS
12 Modern aerospace coatings. Progress in market — Ph.D. Kaverinsky V. S., Kaverinsky D. V.
18 The global market for marine coatings
19 The main trends and challenges of auto refinish — Ph.D. Kaverinsky V. S., Kaverinsky D. V.
BRANCH MARKETING
14 Epoxy resins. The dynamics of the market changes in Russia
15 Acrylic polyols. The dynamics of the market changes in Russia
METHODS OF TESTING
22 Anton PAAR rheometers for control of viscoelastic properties of coatings
36 Possibility of topological calculation of filler mixtures in decorative materials with preference of small fractions — Furman N. N.
Abstract:
A method is proposed for calculating the packing density of filler mixtures with an excess of a finer fraction. A mathematical model of calculation is presented. The packing density and coordination numbers in the layer of abutment of spherical fine particles to a large particle are calculated, depending on the ratio of their sizes. The tendency to change the packing density has been revealed. On the example of two mixtures of micro-marble, the practical applicability of this method is illustrated.
Keywords: discrete topology, packing density, coordination number, fillers, decorative plaster, micro-marble.
RAW MATERIALS. INTERMEDIATES AND PRODUCTS
16 Acrylic coatings for car repair and application on large-size transport - Galkina Yu. V.
26 Metal powders for coatings. Review of technical papers. — Pavlov A. V., Ph.D. Merkulova Yu. I., Zelenskaya A. D., Ph.D. Zheleznyak V. G., Ph.D. Fedyakova N. V.
Abstract:
In this paper, composite coatings with metallic pigments are considered. Paintwork coatings with metallic pigments can be used in various branches of industry: imparting decorative properties to products, creating anticorrosion, heat-conducting, biocidal, wear-resistant coatings.
An attempt is made to generalize scientific literature and modern research in the field of application of metal powders for the creation of paint and varnish composite materials. The work shows various metal powders used to create metal containing coatings: copper, silver, aluminum, zinc, lead, metal alloys. The use of metal powders in the development of paintwork materials leads to the production of functional coatings: coatings with biocidal properties, conductive, heat-resistant, wear-resistant.
Keywords: paints, coatings, metal powders, metallic pigments
32 Restoring the splendor of an imperial past
PRODUCTS AND RESEARCH
42 The research of the correlation of the quantity of the underglaze dyes-solutions and the mixture with ceramic pigments on the decorative properties of coatings — Ph.D. Papulova G. N.
Abstract:
The compositions on the basis of the suspensions of mineral fillers in aqueous-glycerol solution of urea-formaldehyde resin (KF-resin) with the presence of a certain quantity of dye-solution (in particular, chloride of cobalt СоСl2·6Н2О) were studied. The optimal amount of the dye-solution in the paint to achieve the necessary rigidity of the contour (the value of the salt halo, in mm, around the contour of the figure) and the amount of mineral fillers, pigments and a mixture of pigments in the paint to achieve the desired decorative effect were found.
Keywords: ceramic pigments, underglaze dyes-solutions, cobalt chloride, urea-formaldehyde resin
EVENTS
46 Digital life: chemical and petrochemical industry in Russia in the era of digital economics
48 YOUR NAVIGATOR
|
7-8/2018
4, 55 NEWS
EXPERT VIEW
8 Titanium dioxide: supply and demand prospects
39 Pulse of the industry — Averyanov G. V.
BRANCH MARKETING
10 Titanium dioxide. Dynamics of market changes in Russia
11 Titanium dioxide. The structure of consumption in the production of paint in Russia
RAW MATERIALS. INTERMEDIATES AND PRODUCTS
12 Improving pigment dispersion and paint stability with versatile amino alcohols — Severac R., Fernandes Y.
16 Enhancing the ability of coatings for refinishing with the help of new generation of additives — Dr. Sulzbach Horst M., Heecheren Mark, Dr. Eberhardt Mark, Dr. Jonky Guillaume V.
50 Chemically precipitated calcium carbonate (chalk) as a highquality functional additive for solvent based and water-based paints — Dydik O.M.
BUSINESS CLASS
22 Customs immunity: legal practice — Teselkina L., Kurochkina O.
PRODUCTS AND RESEARCH
25 Express method for assessment of biocides efficiency for protection of coatings — Candidate of Biological Sciences, docent Kozlov G. V., Dr. of Chemical Sciences, Professor Garabagiou A. V., Dr. Sc. Drinberg A. S., Pushkarev M. A., Tarasova I. N., Dr. of Chemical Sciences, Professor Mashlyakovsky L. N., Nedvedsky G. R., Maksimova A. M., Mnatsakanyan K. A., Goryunov A. V., Danilovich D. S.
Abstract:
A new express method for assessment of biocides efficiency, used for protection of paint coatings, which allows to evaluate reliably biocide efficiency for 2–5 day (instead of 25–84 day in standard methods) and with the use of only one test-culture instead of 10 is presented.
The biocides efficiency on agar culture mediums and their compatibility with the paint coating system (solubility, coating morphology) have been investigated. Then, the results obtained were compared with those according the standard methods (GOST 9.050-75 “ESZKS. Paint Coatings. Test Methods on Mould Resistance”).It was ascertained, that the proposed express method offers the sensitivity analogous to those in the standard test method on mould resistance of paint coatings, in which not only fungi spores, but also different test-cultures are applied on the surface of paint coatings in order to increase their growth. Comparable tests were made using three biocides and four paint coating systems. The best of the biocides, investigated by both proposed express method, and standard method, was found to be Vantocil 100 (polyhexamethylenebiguanidine hydrochloride).
Keywords: paint and varnish materials, antifouling coatings, mushroom resistance, bio damages, biocides, fungicides, accelerated biocidal test method, methods for testing biocidal and fungi resistance.
42 Аqueous film-forming dispersions for dust collecting compounds — Kireeva E. V., Ph.D. professor Kondrasheva N. K., Ph.D., docent
Zyryanova O. V., Ph.D. Drinberg A.S., Nedvedsky G. R., Nikandrov A. N.
Abstract:
The technical requirements aqueous dust-collecting (DC) compounds have been determined. A technology to produce an aqueous (DC) compounds based on vinyl alkyd oligomers was developed. The structure and volumetric distribution of particles of aqueous dispersion of PU composition are studied. It was found that water nanodispersions with a particle size of 70–90 μm are most effective in the process of dust collection. The tests of PU formulations for frost resistance were conducted. It is established that the optimum content of antifreeze in the aqueous dispersion of PU is 15–20%. Comparative tests of water and organo-soluble PU formulations have been carried out. Experimental batches of PU compositions were tested at mining facilities.
Keywords: dust collecting compounds (DC), film-forming substances, aqueous dispersions, vinyl alkyd oligomers, nanodispersions, antifreezes.
PHYSICO-CHEMICAL RESEARCH
32 Protective epoxy primers: the effect of nature and the ratio of pigments, the content of Zn of various forms on the physicomechanical and anticorrosive properties of coatings — the graduate student Lebedeva E. A., Doctor of Chemical Sciences, Professor Mashlyakovsky L. N., Dr. Sc. Drinberg A. S., bachelor Shikina P. A., Ph.D. Khomko E. V.
Abstract:
Effect of the nature, loading, weight ratio of pigments and zinc percentage of two different shapes in epoxy primers on physical-mechanical and anticorrosion properties of coatings was investigated. Coatings containing zinc of two types with different particles shape (spherical and flaked) provide better anticorrosive protection. Partial replacement of spherical zinc for zinc flakes in epoxy primers allows to reduce its content from 76 to 45 wt %. Epoxy primers with as low as 27 wt % zinc has been developed with additional feeding of another anticorrosive pigments Zn3(PO4)2×H2O (zinc phosphate) and SrCrO4 (strontium chromate). These primers can be used for long-term anticorrosive protection of steel constructions for various purposes.
Keywords: zinc-filled primers, zinc dust, corrosion resistance, tread protection, spherical pigments, flake pigments, specific volume resistance, white corrosion, zinc phosphate, strontium chromate, hematite.
EVENTS
46 New in standardization
48 All flags will visit us — Andrutskaya O. M.
52 YOUR NAVIGATOR
|
6/2018
4, 48 NEWS
ECONOMICS AND STATISTICS
9 Corrosion control coatings
24 State and progress of resins market for coatings
BUSINESS CLASS
12 Is this unrealistic? It is interesting! Cases for creating new products
PRODUCTS AND RESEARCH
16 Polycarboxylate modifiers of pigments surface — Zakharova N. A., PhD. Professor Indeikin E. A.
Abstract:
Оligomers with a high content of carboxyl groups in the main chain were investigate. The values of hydrophilic-lipophilic balance of these oligomers in protonated and salt form are calculated and the possibility of their use as surfactants is shown. The dissociation and hydrolysis constants of studied surfactants were determined by potentiometric method. We determined the cloud point of aqueous solutions of the surface-active substances. It is shown that the synthesized polymers can be used as modifiers of iron oxide pigments. It is established that the carboxyl-containing polymer surfactant chemisorbed on the surface of goethite particles, significantly change its properties, especially twice reducing its oil absorption, which can significantly increase the content of the polymer composite material and more than ten times the accelerate the dispersion process is extremely energy-intensive step of producing pigmented materials. Lightness and hue of pigments have not changed.
Keywords: polymer, hydrophilic-lipophilic balance, dissociation constant, hydrolysis constant, point cloud point, modification.
RAW MATERIALS. INTERMEDIATES AND PRODUCTS
20 How legislation is affecting the development of epoxy paints
26 Isocyanates of the brand ATTONATE — Galkina Yu. V., Nikol'skaya O. S.
TINTING TECHNOLOGIES. COLORIMETRY
28 Industrial tinting system CIU
STANDARDIZATION AND METROLOGY
30 Protective paint and varnish coatings for concrete and reinforced concrete structures — Doctor of Technical Sciences, prof. Stepanova V. F., Sokolova S. E., Polushkin A. L.
Abstract:
A generalized approach to the evaluation of the effectiveness of protective paint coating systems for concrete and reinforced concrete structures is proposed. The main evaluation criteria and test methods for protective paint coatings on concrete (water impermeability, adhesion, crack resistance, frost resistance, diffusion permeability, etc.) are given.
Effective systems of protective coatings for concrete on the basis of paint and varnish materials (paint and varnish thin-layer, lacquer-and-paint thick-layered, combined and impregnating-colmatizing) are considered.
The results of tests of various coating systems on the basis of polyurethane paint and varnish materials on concrete on the main quality indicators in comparison with unprotected concrete are made in the laboratory of corrosion and durability of concrete and reinforced concrete structures NIIZhB.
Keywords: protective coatings, polyurethane coatings, corrosion of reinforced concrete structures.
NANOTECHNOLOGY
35 Catalytic effect of carbon nanoparticles on the thermolysis of intumescent coatings — Ph.D., associate professor Zybina O. A., Dr. tech. sci., Professor Babkin O. E., Dr. tech. sci., Professor Snegirev A. Yu.
Abstract:
Intumescent paints are designed to produce fireproof reactive coatings which swell or expand under the influence of fire with generation of coke cellular material layer which decreases heat and mass transfer to the protected surface. The article deals with some of results of the work connected to a modification of swelling fireproof coating by carbon framework structures. It is shown that carbon nano-additives (fullerenes, nanotubes, endofullerenes, graphene) provide better fire protective behavior of the intumescent coating, which is explained by their influence on the formation of the intumescent layer structure which is more resistant to the influence occurring during the fire. It is shown the addition of carbon nanoparticles to the composition improves swelling mechanical, thermal-acid stability, fire-resistance, etc. It was established that the carbon nano-additives exhibit catalytic activity at the initial stage of the thermolytic synthesis of coke cellular material layer at 170–240 ° C by the method of microcalorimetry.
Keywords: fire protection, intumescent coating, flame retardants, nano-fillers, nanocomposites, carbon framework structures, fullerenes, nanotubes, endofullerenes, graphene.
INFORMATION TECHNOLOGIES
41 Digital technologies: Industry 4.0 in the paint and varnish industry — Kaverinsky D. V., Ph.D. Kaverinsky V. S.
45 YOUR NAVIGATOR
|
5/2018
4, 47 NEWS
ECONOMICS AND STATISTICS
8 Coatings for floors — a promising area of the construction industry
14 Additives Market Review
36 The market of paint and varnish materials for wooden furniture
RAW MATERIALS. INTERMEDIATES AND PRODUCTS
16 RHEOLATE® — pseudoplastic associative thickeners for paint and coating systems
37 Characteristics of the photopolymer coatings for optic cable — Dr.Sc. Babkin O. E., Babkina L. A., Andreeva N. A., Danilovich D. P.
Abstract:
The production of optical fiber in Russia is a new direction of the industry, where innovative materials and technologies are used. The article presents the characteristics of varnish primer and coating varnish for fiber optical cables and methods for their research.
Keywords: optical cable, photopolymer coatings, glass transition range.
PRODUCTS AND RESEARCH
19 Combination of water-based dispersion of paraffin and ceresin with polymer dispersions — Tereshko A. E., Prof. Indeikin E. A.,
Prof. Golikov I. V.
Abstract:
The compatibility of polymer dispersions with water-based dispersions of solid petroleum hydrocarbons was studied. As the objects of the investigation were used dispersions of polymers of different chemical nature: polyvinylacetate, polyurethane, polyperchlorovinylacrylate, copolymers of styrene with butyl(meth)acrylate and butadiene. Water-based dispersions of polymers and water-based dispersions of hydrocarbons were combined. The water-based dispersions of the petroleum paraffin and the ceresin developed by us were used. The dispersion of paraffin is stabilized with polyvinyl alcohol, and the ceresin dispersion is stabilized with an anionic surfactant. The pH areas providing of compatibility and stability of such dispersions was established by the electrokinetic researches. Presence of hydrocarbon dispersion in the system in most cases reduces the initial coagulation rate and increases the aggregative stability of the system was shown. The effect of petroleum hydrocarbons on the change in the surface energy of coatings formed from the combined dispersions was investigated. Coatings were formed both under ordinary conditions and at temperature exceeding the melting point of paraffin and ceresin (70 °C). The surface energy of coatings decreases even with a small content of hydrocarbon in the coatings (up to 10%) was established. Heat treatment allows to reduce the surface energy by another 3–5 mJ/m2. As a result of heat treatment, a microstructure consisting of paraffin crystals is formed on the surface of the polymer coating, which increases the order and dispersion hysteresis of wetting. Thus, the physicochemical conditions for combining of paraffin and ceresin dispersions with polymer dispersions have been established.
Keywords: water-based dispersions, paraffin, ceresin, compatibility of polymer dispersions, electrokinetic researches, surface energy.
40 Research on the impact of titanium dioxide of different trademarks on the process of thermolysis of intumescent fire-protective coatings — Ustinov A. A.,Zybina O. A. , Dr.Sc. Babkin O. E.
Abstract:
The paper overviews the role of titanium dioxide as a component of intumescent coatings in the process of their thermolysis. It is stated that the properties of a charred layer forming from an intumescent coating must correlate with the properties of titanium dioxide's species, such as surface treatment and crystalline structure. Thermal analysis proves this statement showing that rutile titanium dioxide helps forming a charred layer which has the highest thermal stability thus an intumescent's efectiveness grows up. It is shown that the quality of primary products is extremely important for intumescent compositions as they must operate reliably in case of fire; and knowledge of processes that happen within the composition provides an opportunity to find the best-performing ingredients.
Keywords: fire safety, fire protection, swelling coatings, intumescent compositions, fire-protective paints, thermolysis, titanium dioxide, thermal analysis, derivatography, swelling coefficient.
INTERVIEW
12 Floor has the meaning
32 For us, the production of a quality product is a matter of principle
LOGISTICS
24 Ride on the tank
EVENTS
18 Problems and prospects for the development of the DIY market for building and finishing discussed at the forum DIY–2018
44 YOUR NAVIGATOR
|
4/2018
CONTENT
4, 47 NEWS
PRODUCTS AND RESEARCH
8 Modification of epoxy emulsions by inorganic electrolytes — Ph.D. Shinkareva E. V.
Abstract:
The effect of the chemical nature and concentration of the inorganic electrolyte on the stability of aqueous epoxy emulsions and their rheological properties. It is found that the presence of inorganic electrolytes in the emulsions in certain concentrations can reduce the size of the dispersed phase (dispersion causes the spontaneous) and leads to the disappearance of viscosity anomaly minima and maxima on the curves of flow and, therefore, — reducing power consumption during emulsification.
Keywords: epoxides, water emulsions, flow curves.
12 Analysis of the size distribution for pigments and dyes
14 Anti-mold composition for water-dispersed polyacrylic paints — Taramasova D. R., D.Sc. Rakhmatullina A. P., Voiloshnikov V. M. , Ph.D.
Perushkina E. V. , Ph.D. Semenova E. N.
Abstract:
The “Antimold” composition is developed on the basis of the silicone rubber waste destruction product and tested. It is a complex of a bactericidal additive in a solution of the destruction product and a water dispersion of a styrene copolymer and acrylic acid esters. The optimal composition of the components is developed.
Keywords: siloxanes, waste, styrene, acrylic acid.
20 Spreading of the epoxy-polyester powder coatings melts — Kotova D. S., Dr. chem. sci. Professor Indeikin E. A.
Abstract:
The powder coatings formation is associated with the transition of polymers or oligomers from a glass state to a viscous flow, followed by spreading and curing (in the case of thermoset materials). The processes during the formation of matt and glossy powder materials were analyzed using the DSC-method. There is a large variance in the differential spreading curves of the epoxy oligomer, polyester, and mixtures thereof. This is due to the fact that the presence in the solution of components differing in structure and chemical composition disrupts the complementarity of molecules, reducing the possibility of orientational intermolecular interaction. This leads to a decrease in the viscosity of the melt and, correspondingly, to an increase in fluidity. The influence of pigmentation on the powder coatings spreading rate was also studied. It should be noted that in spite of the close values of VCP, and for matt coatings, practically the same, relatively small amounts of color pigments significantly and differently affect the spreading of melts. Pigmentation by titanium dioxide (white powder coating) leads to the most significant increase in spreadability, the least increase was with phthalocyanine green pigment and technical carbon.
For glossy powder coatings, the pigmentation results in an increase in the spreading speed for the powder material. The spreading process of matt samples, additionally containing epoxy resin incompatible with the basic epoxy-polyester matrix, depending on the pigment type used, is accelerated or slowed down compared to the unpigmented material.
Keywords: powder coatings, epoxy oligomer, polyester, matting, pigmentation, spreading rate of melts.
24 Influence of climatic factors of tropical and temperate (moderate) climate on properties of paint coatings on urethane basis — Ph.D. Andreeva N. P., Ph.D. Pavlov M. R., Ph.D. Nikolaev E. V., Dr. Slavin A. V.
Abstract:
In work results of environmental climatic tests are given in various zones of tropical and moderate climates of paint coatings which are widely applying to coloring of air transport. The assessment of results of keeping of protective, decorative and physicomechanical properties of the considered materials depending on the exposure location is carried out.
Keywords: environmental climatic tests, paint coatings, ageing of coatings, air transport.
POWDER COATINGS
18 Powder coatings — today and tomorrow — Ph.D. Kaverinsky V. S., Kaverinsky D. V.
PHYSICO-CHEMICAL RESEARCH
30 Study of the infl uence of salt-acid salts of some metals in the composition of high-completed water paint-and-paint material on the properties of coatings on ceramic surfaces — Ph.D. Papulova G.N.
POINT OF VIEW
37 Problems of antimicrobial coatings
COMPANY PORTRAIT
40 Company “Russkie kraski” — 180 years!
EVENTS
33 Territory of competences
42 WACKER opens new laboratory for adhesives and sealants in the Moscow technical center
44 YOUR NAVIGATOR
|
3/2018
CONTENT
4, 51 NEWS
ECONOMICS AND STATISTICS
8 European coatings market
EXPERT VIEW
34 Iron oxide have been as pigment forever
PRODUCTS AND RESEARCH
15 The influence of chemical structure of fluorine-containing organosilicon copolymers on moisture resistance of epoxy resin cured by amines — Parshina M. S., Soldatov M. A., Makarova V. A., Serenko O. A., Muzafarov A. M.
Abstract:
The compositions based on epoxy resin and fluorine-containing organosilicon copolymers were investigated. It is shown that random copolymers containing in its composition branched fluorine-organosilsesquioxane, phenylsilsesquioxane and linear methylvinylsiloxane links are characterized by a low compatibility with epoxy resin, which depends on the content of linear methylphenylsiloxane blocks in the copolymer structure and increases with an increase in their number. Introduction to epoxy resin is 0.5 wt. % copolymer in which the ratio fluorine -organosilsesquioxane, phenylsilsesquioxane and linear methylvinylsiloxane units is 1:1:1, leads to lower moisture absorption epoxy composition is more than 2 times. It is shown that the use of copolymers, containing units with different function in relation to modifiable matrix, target selection of their composition is a promising method of increasing the hydrophobicity and moisture resistance of epoxy resin coatings.
22 Production of titanium dioxide in processing of low-titanium slag - Dr. Sc. (Engineering) Gerasimova L. G., PhD. (Engineering) Shchukina E. S., Dr. Sc. (Engineering) Maslova M. V.
Abstract:
The technology of low-titanium raw materials, including titanium slag, isolated during carbothermic reduction of the Khibinsky titanomagnetite has been investigated. The chemical composition of the slag - TiO2 - 65%, chromophore impurities in the form of compounds of manganese, chromium and vanadium was established. Conditions are found under which sulfuric acid technology produces titanium dioxide of high purity - 99.5% TiO2. The achievement of such a result contributes to pre-treatment of the slag with dilute mineral acids at which manages the main free from iron masses, partially extracted chromophore elements. At the same time the content of titanium in the slag increases by more than 15%. Sulfuric acid decomposition of such slag with 80% H2SO4 and subsequent aqueous treatment of the sulphate sinter provides leaching of titanium to form a sulfate solution, from which a hydrated product practically free of impurities is formed by thermal hydrolysis, which takes place in the presence of a reducing agent (Zn powder). The specific composition of the solution and the conditions for conducting hydrolysis made an impact on the structure of titanium dioxide and, accordingly, its surface properties. In particular, when using a low-concentration titanium prehydrolysis solution, titanium dioxide is obtained in the form of anatase with a specific surface of particles equal to 50-55 m2/g. Rutile with a denser structure is formed from a solution with a higher concentration. Thus, by regulating the technological parameters, it is possible to expand the range of obtained products and, accordingly, the field of its use: in the production of paint and building materials in the production of ligatures, condensers, and also in the compositions of heat-resistant glues and plastics.
27 Oxidation of zinc particles by oxygen of air in the presence of the DYNASYLAN MKS ethylpolysilicate. The influence of hydrophobic aerosil and nano-carbon tubes on the properties of the zincysilicate composition — Ph. D. Shinkareva E. V., Statkevich P. I.
Abstract:
Methods of differential thermal and X-ray phase analysis were used to study the oxidation of Zn-Dust zinc dust particles in air with oxygen in the air with the ethylsiliconate binder of Dynasylan MKS brand. It was shown that the oxidation of zinc particles begins when the temperature reaches 315 °C, in the presence of Dynasylan MKS — at 450 °C. The composition of the zinc silicate primer enamel modified with NSU-5 carbon nanotubes and AEROSIL R 972 hydrophobic aerosol was developed. The rheological properties of the compositions, as well as the physicochemical properties of the coatings and their structure, were studied.
36 Estmation of fire hazard of thin-layer paint-and-lacquer coatings —Dr.techn. sci., professor Konstantinova N. I., Krivoshapkina O. V. , Ph. D. Shebeko A. Yu., Goltsov K. N.
Abstract:
The issues of fire hazard of finishing and facing building materials and products covered with paint-and-lacquer coatings (PLC) are considered in the paper. There are provided comprehensive experimental investigations in evaluation of combustibility, inflammability, flame spreading on the surface, smoke generation and toxicity of combustion products of some facing materials that consist of incombustible base and PLC differ in chemical composition and thickness. The value of thickness of PLC, applied on incombustible base, that is safe in the view of fire safety was ascertained during investigations. This value was 300 microns.
There are elaborated the proposals for amendment to the project of new edition of SP 2.13130 concerning possibility of applying of combustible materials of protective-and-decorative finishing with thickness up to 0.3 mm that are applied on incombustible external surface of exterior walls (including facing and finishing of façade systems) for buildings of all classes of functional fire safety including F1.1 and F4.1 classes.
Keywords: fire safety of finishing and facing building materials and products, paint-and-lacquer coatings (PLC), fire safety parameters, fireproof thickness of layer of protective-and-decorative finishing of building and structures
RAW MATERIALS, INTERMEDIATES AND PRODUCTS
12 Melamine-formaldehyde resins of the brand ATTLAMINE — Yu. V. Galkina
44 On the creation of recipes of effective fire-protective coatings for building construсtions — Ph.D., Associate Professor Zybina O. A., Dr. techn. sci., Professor Babkin O. E.
Abstract:
The roles of main components of fire-protective swelling compositions (ammonium polyphosphate, pentaerythritol, melamine, titanium dioxide and polymer binder) are overviewed. It is shown that well-known principles of creation of intumescent compositions are not exactly correct, as the impact of their components on the process of building of a charred layer is not fully studied. It leads to creation of low effective intumescent compositions. The information about an intumescent process and the role of intumescent components is revised and this fact gives an opportunity to create more effective fire-protective paints.
Keywords: fire protection, fire-protective composistions, intumescents, fire-protective paints, ammonium polyphosphate, pentaerythritol, melamine, titanium dioxide.
EVENTS
20 Development in partnership with AZELIS RUS — O. M. Andrutskaya
42 Mulled wine from homa — 2018
49 YOUR NAVIGATOR
|
1-2/2018
CONTENT
4, 61 NEWS
ECONOMICS AND STATISTICS
10 Global coatings market
12 Russian coatings industry in 2017 — O. M. Andrutskaya
22 Analysis of heat-resistant coatings market in 2012– 2016. Forecast until 2025 — Ph.D. Kislova Yu.E.
EXPERT VIEW
14 Seven steps to increase in selling prices
PRODUCTS AND RESEARCH
18 Problems of adhesion strength of UV-curing coatings — Dr. techn. sci. Babkin O. E., Babkina L. A., Il'ina V. V., Melidina A. A.
Abstract:
The paper presents data on the study of the processes of formation of coatings from photopolymer compositions using ultraviolet curing technology. On the example of compositions based on aliphatic urethane acrylates with the addition of monomers of acrylic series with different functionality and promoters of adhesion, the mechanisms of polymerization inside the layer of the formed coating are considered. The applied method of Raman spectroscopy allowed us to prove that for thin- (up to 100 μm) and thick-layer (for 300 μm) coatings, a different degree of conversion of double bonds in the depth of the coating and different efficiency of the post-exposition polymerization during light storage are characteristic. The obtained data are related to the experimental data on the change in the adhesion strength of coatings during storage.
Keywords: coatings, photopolymerization, UV-curing, adhesion strength.
28 Identity and merchandising expertise of paint products in her customs declaration — Ph.D., Associate professor Lyashko A. A.
Abstract:
The article reflects the importance of identity and merchandising expertise of paint products within the customs control, the main types of offences in the field of customs legislation during the customs Declaration paint products, as well as the results of the study semi-finished alkyd varnish GF-012W.
Keywords: customs control, commodity expertise, declaring of varnish-and-paint products.
40 Wear resistance of coatings — Pavlov A. V., Ph.D. Merkulova Yu. I., Zelenskaya A. D. , Ph.D. Zheleznyak V. G.
Abstract:
In this paper we consider composite coatings that have wear resistance, varieties of destruction of coatings due to wear, as well as options for reducing it by creating coatings based on film-forming substances of various chemical nature and functional additives, including nanosized fillers that can be introduced in small quantities in industrially produced varnish-and-paint materials, while improving the performance characteristics of the coatings obtained on their basis.
An attempt is made to generalize scientific literature and perspective developments in the field of wear-resistant coatings. The work shows film forming agents, fillers, including nanopowders, used to create wear-resistant coatings.
Keywords: wear resistance, coatings, fillers.
RAW MATERIALS, INTERMEDIATES AND PRODUCTS
33 Mica MICAFORT for light, solvent-based anticorrosion coatings — Dr. Sakis Chatzitnikolau
44 Fire protection with intumescent coatings under the hydrocarbon fire conditions — Ph.D. Drinberg A. S., Ph.D. Gravit M. V., Ph.D. Zybina O. A.
Abstract:
The methodological approaches fixed in Russian and foreign normative documents concerning the application of paint coatings to ensure the specified fire resistance of building structures during the modeling of the hydrocarbon combustion regime are investigated. It is shown that the use of protective equipment in conditions of the hydrocarbon fire regime abroad is regulated by internal industry standards. In Russia, there is no necessary normative and experimental basis for justifying the methodology for testing the fire resistance of building structures with the modeling of the hydrocarbon fire regime. The comparative characteristics of imported fire retardant coatings effective in the conditions of hydrocarbon burning and the results of fire laboratory tests of several domestic epoxy coatings intended for the fire protection of metal structures from a hydrocarbon fire are given.
Keywords: fire retardant coatings, oil and gas complex constructions, building structures, fire resistance limit, fire protection means, intumescent coatings, flame retardant efficiency, temperature regimes of fire, cellulose combustion, hydrocarbon combustion.
50 Polyurethane aqueous dispersions without solvents BAYHYDROL® UH for wood coatings: existing opportunities and new developments — Eroma B. L.
54 Fluoropolymers LUMIFLON® for high-quality finishing coatings with a long service life
EVENTS
37 International Coatings Forum 2018 program
56 3M expands business in Russia
58 YOUR NAVIGATOR
|
12/2017
CONTENT
4, 54 NEWS
ECONOMICS AND STATISTICS
11 The market for UV-curable coating materials: analysis and forecasts
PRODUCTS AND RESEARCH
12 Features of technology of application of UV-curing compositions on optical fiber — Ph. D. Babkin O. E., Babkina L. A., . Il’ina V. V
ECOLOGY AND RESOURCE EFFICIENCY
16 The solution of the problem of gelation in the synthesis of alkyd resins based on bio-succinic acid
RAW MATERIALS. INTERMEDIATES AND RODUCTS
20 Film-forming agents for coatings with high solids. Isocyanates brand Attonate — Galkina Yu. V.
28 Technical solutions for waterproofing membranes from the company Larchfield LSN — Ogneva A.
32 A new pure acrylic binder for problem-free, exterior masonry coatings with extended application window. Part 2 — Secher M., Airaud C., Baude C., Bousseau E., PhD. Fream A., Zhukov R.
POINT OF VIEW
25 You need to be ready for new surprises — Ph.D. Kaverinsky V. S, Kaverinsky D. V.
EXPERT VIEW
36 Cobalt driers and again problems?
PHYSICO-CHEMICAL RESEARCH
38 Paint-cadmium-polymer coatings obtained by method of cathodic electrodeposition — Lwin Ko Ko, Pelyasova D. A., Ph.D. Kvasnikov M. Yu.
EVENTS
7 A comprehensive analysis of pigment concentrates
43 CHEMISTRY grows
48 INDEX OF ARTICLES PUBLISHED IN 2017
51 YOUR NAVIGATOR
|
11/2017
CONTENTS
4, 46 NEWS
ECONOMICS AND STATISTICS
10 Situation at European coatings market
PHYSICO-CHEMICAL RESEARCH
12 The choice of dispersant using the parameters solubility by Hansen
RAW MATERIALS, INTERMEDIATES AND PRODUCTS
15 Driers brand ATTDRY for alkyd coatings — Galkina Ju. V.
20 ALTIRIS — titanium dioxide by HUNTSMAN PIGMENTS & ADDITIVES (VENATOR) for special purpose — Businer L. Yu.
POINT OF VIEW
18 Silicone fluids are the most preferred slip additive to meet product durability requirements
AUTOMATION
22 Test track for coatings
TECHNOLOGIES AND EQUIPMENT
26 The new technology of cleaning equipment in the paint industry — Ph.D. Kaverinsky V. S., Kaverinsky D. V.
EVENTS
28 It was smooth on paper... — Andrutskaya O. M.
METHODS OF TESTING
30 Topological method of calculating the composition of polydisperse mixtures of fillers and forecasting the properties for decorative
finishing — Furman N. N.
PRODUCTS AND RESEARCH
38 Innovation ways for designing new color and optical effect — Ph.D. Kaverinsky V. S., Kaverinsky D. V.
43 YOUR NAVIGATOR
|
10/2017
CONTENT
4, 55 NEWS
ECONOMICS AND STATISTICS
10 Analysis of the Russian market of fire retardant paints for steel structures in 2012–2016. Forecast until 2025 — Ph. D. Yulia Kislova
24 The European coatings market in 2017
POINT OF VIEW
17 Problem of coatings safety must be solved by joint efforts — Ph.D. Kaverinsky V. S.
48 The staff problems in industry — Averyanov G. V.
PACKAGING
20 Innovation vs classics: the transport of liquid chemicals in drums and IBC-containers
RAW MATERIALS, INTERMEDIATES AND PRODUCTS
22 Resins for the chemically resistant coatings — Galkina Yu. V.
36 New industrial coating materials — academician, Professor, Ph. D. Figovsky O. L., academician, Professor, Ph. D. Kudryavtsev P. G.,
Leykin A. D., Ph. D. Shapovalov L. D., Ph. D. Ioelovich M. Ya.
PRODUCTS AND RESEARCH
25 Barrier against rust by pure, platy talc — Kilpeläinen V.
30 Leveraging surfactant structure-property relationships to address emerging needs in coatings — Christine Louis, K. Michael Peck
AUTOMATION
41 Quality Control in formulating and automated systems — Tretyakov I. V.
INTERVIEW
44 Driver of economic growth, or What will be the main topic of discussion at the V Moscow chemical forum?
EVENTS
46 RUCOLOR–2017: focus on major problems in the industry — Andrutskaya O. M.
52 YOUR NAVIGATOR
|
9/2017
CONTENT
4, 47 NEWS
EVENTS AND FACTS
9 The principles of cooperation at creating new coatings — Ph.D. Kaverinsky V. S., Kaverinsky D. V.
ECONOMICS AND STATISTICS
13 Outstripping growth of direct-to-metal coatings
RAW MATERIALS, INTERMEDIATES AND PRODUCTS
17 New raw materials for corrosion-resistant coatings (review)
PRODUCTS AND RESEARCH
24 Possible ways to improve technological and physical-mechanical properties of zinc-rich primers — Pavlov A. V., Miloradova E. A., Garustovich I. V. , Ph.D. Shishilov O. N., Ph.D. Subbotin V. E., Shchepetova A. Yu., Yakovenko T. V.
29 Wetting and dispersing additives. Past and future challenges — Dr. Horst M. Sulzbach, Dr. Michael Bessel, Janos Hajas
PHYSICO-CHEMICAL RESEARCH
23 Experience in operating system for corrosion rate measurement «MONICOR-2M», set in the framework of the national research university Kazan State Technical University — Mukatdisov N. I., Farkhutdinova A. R., Ph.D. Elpidinski A. A.
NANOTECHNOLOGY
20 A barrier against corrosion
39 Synthesis and application of nanoparticles of manganese dioxide in coatings for protection of rolled metal — Ph.D. Katnov V. E., Grishin P. V. , Katnova R. R., Ph.D., prof. Stepin S. N.
44 YOUR NAVIGATOR
|
7-8/2017
CONTENT
4, 53 NEWS
ECONOMICS AND STATISTICS
13 Interation between coating industry and Russia’s government
TINTING TECHNOLOGIES. COLORIMETRY
16 Past and Future of Universal Colorants in Coatings — Frank Kleinsteinberg
20 Software for points of sale (POS) — Sergey Begunov
22 Color measurement of liquid automotive paints
38 Hidden influence. How the color of the primer helps to reveal the potential of the base color paint
EQUIPMENT
24 Service program of COROB company
PRODUCTS AND RESEARCH
29 Giving dirt the brush-off. Easy-to-clean properties now available for epoxy resin systems — Majdi Al-Masri, Wolfgang Griesel, Lin Xie
34 Use of sphenite ores in technology of titanium compounds — Ph. D. (Engineering) Shchukina E. S., Kiselev Yu. G., Dr. Sc. (Engineering)
Gerasimova L. G.
44 The research of correlation of the physico-chemical characteristics and structure of CF-oligomers on paint coating properties for ceramic
surfaces — Ph. D. Papulova G. N.
RAW MATERIALS, INTERMEDIATES AND PRODUCTS
39 Protective coatings based on fluorinated polymers — Dr. Sc. Drinberg A. S., Dr. Sc. Karpov V. A., Okhrimenko A. G.
SUSTAINABILITY AND RESOURCE EFFICIENCY
48 Future of water-borne coatings under threat
EVENTS
26 New features of effect pigments — Andrutskaya O. M.
50 YOUR NAVIGATOR
|
6/2017
CONTENT
4, 55 NEWS
ECONOMICS AND STATISTICS
9 Water-dispersible paints: optimistic or pessimistic forecast and reality
INTERVIEW
8 Effective or bogus?
RAW MATERIALS, INTERMEDIATES AND PRODUCTS
12 EPS® 572 — new modifed acrylic dispersion for special architectural coatings — Massimo Longoni, David Greener
16 Passive fre protection for hydrocarbon fre — Dybal D. A., Ph. D. Shishilov O. N.,Garustovich I. V.
20 Intumescent сoatings: the latest developments in truly functional coatings that save lives — Christophe Baude, Maurille Sécher, Cécile Fonteneau, Dr. Alan Fream, Roman Zhukov
28 New components for the formulations of flame retardant materials
30 Binder for thermal and chemically resistant materials — Galkina J. V.
32 Flame retardant materials of LTD “Teplochim” — Nateikina L. I., Shikhaliyev E. A.
40 Thermo-radiation stable enamel KO-864, on the basis of domestic raw materials — Tarasova I. N., Denisov A. A., Ph. D. Drinberg A. S., Lakeev I. G., Gerwart A. Yu.
PRODUCTS AND RESEARCH
36 The study of the effect of the ceramic pigment in the composition of the highly flled paint material on the physico-chemical properties of coatings on ceramic surfaces — Ph. D. Papulova G. N.
43 A study of the process of obtaining printing inks based on disperse paste — Antropova I. A., Merkulov K. E., prof. Menshikov V. V., Sandu R. A.
EVENTS
48 A new record of the exhibition EUROPEAN COATINGS SHOW — O. M. Andrutskaya
53 YOUR NAVIGATOR
|
5/2017
CONTENT
4, 56 NEWS
ECONOMICS AND STATISTICS
8 The market for construction coating materials: problems and ways of their solution
28 Rising prices for raw materials is a new challenge to the coatings industry
RAW MATERIALS, INTERMEDIATES AND PRODUCTS
15 Market trends for construction paints and novelties of WACKER
21 A new pure acrylic binder for problem-free, exterior masonry coatings with extended application window— M. Secher, C. Airaud, C. Baude, E. Bousseau, Ph.D. A. Fream, R. Zhukov
33 Protective coating on the basis of alkyd resins — Galkina Ju. V.
36 Pigments for 2K-polyurethanes in the product line AO «AFAYA» — Buziner L. Yu.
40 Photochemical reactions on the surface of polymers and coatings — Ph. D. Drinberg A. S., Ph. D. Pavlovich A. V.
ENVIRONMENT AND RESOURCE
30 Diphenylolpropane followed by dangerous titanium dioxide, what is next?
EVENTS
46 Investments in the production of industrial paints.Opportunities and prospects of the Sverdlovsk region
48 INTERLAKOKRASKA–2017 shows the revival of the market
|
4/2017
CONTENT
4, 47 NEWS
ECONOMICS AND STATISTICS
8 The market of paints and varnishes for wood
10 Tasks of the Belarusian market — to develop paint and varnish production and adapt it to the changed conditions
PRODUCTS AND RESEARCH
14 Exploring the chemistry behind silicone-based release additives — Thorsten Schierle
METHODS OF TESTING
20 A method for controlling the development of corrosion on samples of steel with a paint coating — Ph.D. in physicomathematical sciences V. O. Startsev, A. S. Frolov
RAW MATERIALS. INTERMEDIATES AND PRODUCTS
24 Acrylic and styrene-acrylic water dispersion in the formulations of paints for painting metal — Pavlikova S. M., Ph.D. Anisimova S. V., Shurigina U. N.
29 Modifed thiokol compositions and their use as waterproofng and protective paint coatings — Dr. Sc. Storozhuk I. P., Ph.D. Pavlyukovich N. G.
34 Synthesia pigments for powder paints — Khlostova Lenka , Yeglik Tstirad , Buziner Leonid
37 New problems and solutions for manufactures of alkyd coatings. Antioxidants. Anti-skinning additives — Ph.D. V. S Kaverinsky, D. V. Kaverinsky
EVENTS
17 Glintwein from homa — 2017 — Andrutskaya O. M.
40 Raw materials market novelties are in the focus of Coatings Forum — Andrutskaya O. M.
44 YOUR NAVIGATOR
|
3/2017
CONTENT
4, 83 NEWS
ECONOMICS AND STATISTICS
6 The Russian paints and varnishes market in 2016 – Olga Andrutskaya
BRANCH MARKETING
10 Forecast of development of Russian market of water-dispersion paints and varnishes until 2020 with breakdown into segments the segments — PhD Kislova Julia
POINT OF VIEW
18 Chemical distribution in Russia: not bad 2016 and optimistic 2017 — Ivanov Yuri
TINTING TECHNOLOGY. COLORIMETRICS
32 Stability of the CROMSHADE CB 711 LW, a colour paste based on Carbon Black
PRODUCTS AND RESEARCH
34 Anti-corrosion properties of coatings with manganese compounds pigmentation, obtained by ceramic method — Phd, associate
professor Ziganshina M. R., PhD, prof. Stepin S. N.
56 Low surface energy UV-curable powder coatings — PhD, prof. Mashlyakovsky L. N., PhD Pirozhnikov P. B., PhD Korolev I. V., PhD
Kuzina N. G., PhD Khomko E. V.
68 Water-dispersed anticorrosion primer based on epoxy emulsion, nanoparticles and crosslinking agent EPILINK 701 — PhD
Shinkareva E. V.
RAW MATERIALS. INTERMEDIATES AND PRODUCTS
22 Painting of composite materials – PhD Andrey Drinberg
42 Water-based coatings — Natalya Kulikova
46 Paint production for pre-painting in Russia — Dr. Kuleshova I. D.
TECHNOLOGIES AND EQUIPMENT
52 Non-waste managed synthesis technology for ZnO to obtain a product with different dispersity — Estrin I. A., Koretsky I. V.
80 YOUR NAVIGATOR
|
1-2/2017
CONTENT
4, 16, 62 NEWS
POINT OF VIEW
12 The Russian market of titanium dioxide: after «Titanic» or towards new horizons? — Ivanov Yu. E.
18 Mergers and acquisitions in the west and their impact on the Russian paint market — Averyanov G. V.
ENVIRONMENT AND RESOURCE
17 Safe future
PRODUCTS AND RESEARCH
25 Synthetic composite fillers and their properties — Dr. Gerasimov L. G. , Ph. D. Maslovа M. V., Ph. D. E. S. Shchukinа, Kiselev Yu. G.
40 The influence of pentaerythritol’s properties on thermolysis of flame retardant intumescent paints — Ph.D. Zybina O. A., Gavakhunova R. A., Dr. Sci. Tech. Babkin O. E., Dr. Sci. Tech. Silnikov M. V.
44 Long-term corrosion protection of the passenger carriages: problem analysis — A. I. Simonov, Ph. D. T. A. Romanova
48 Coating for cathodic electrodeposition based on polyelectrolyte film former and zinc acetate — Pavlov A. V., Ph. D. Kvasnikov M. Yu.,
Baranov N. O., Zelensky A. D., Batalov R. S.
54 A study of the sorption capacity of the water-soluble ureaformaldehyde oligomers having different aggregate stability, on
the ceramic surface — Ph. D. Papulova G. N.
RAW MATERIALS. INTERMEDIATES AND MATERIALS
20 Silicone modifiers for polyurethane coatings with improved properties — Ph. Chernyshov D. D.
33 New solutions for corrosion protection — Ph. D. Kaverinsky V. S., KaverinskyD. V.
51 Coating for glued laminated timber — Dr. Drinberg A. S., Vyzhletsova T. E.
EVENTS
30 New equipment by «TEKSA Khimmash» — Andrutskaya O. M.
36 International Coatings Forum
58 YOUR NAVIGATOR
|